The AAC-801 ionizing air blower's Faraday Balance System assures low offset voltage or balance automatically. It offers greater efficiency and easier cleaning than conventional ionizers. The Bench Top Ionizer is designed to neutralize static electricity from insulators and isolated conductors in localized work areas in assembly rooms, wave solder lines, laboratories, QC, test stations, packing and shipping areas and clean rooms.
Air ionization can neutralize the static charge on insulated and isolated objects by producing separate charges in the molecules of the gases of the surrounding air. When an electrostatic charge is present on objects in the work environment, it will be neutralized by attracting opposite polarity charges from the ionized air. Note that ionization systems should not be used as a primary means of charge control on conductors or people. (Reference: IEC 61340-5-2:1 paragraph 5.2.9).
Intelligent modern, exquisite appearance, fine production, novel design.
Remote control and touch dual control power supply to start and adjust wind power.
It has the function of high-voltage fault wind alarm and alarm lamp prompt, and has double intuitive understanding of hearing and vision Prepare to work properly.
Lock the wind speed by remote control lock screen and standardize the static electricity removal of ion blower in workshop.
When the fan encounters obstacles in the normal operation process, the fan will automatically short-circuit and stop working.
High speed of static electricity removal, low balance voltage and high safety performance.
Automatic switch between cold and warm air.
Buzzer/red light flashing
Auto clean button
Auto clean every 8 hours
Ion output voltage
Frequency conversion 5.0KV
100-240 VAC, 50/60 Hz
2.0 sec (30 cm) (1000-100V high fan speed)
Remote control/touch dual start,on/off, fan speed control low/medium/high, heater on/off
AC Power Cord outlet
55cfm (low), 110 cfm (high fan speed)
45 dB (low fan speed), 55 dB (high fan speed) ,measured at 2’ in front of blower
Temperature 0℃- 50 ℃, Humidity 20% -75% RH
Cold rolled steel plate
186*100*240 mm (with stand)
2.7kg with stand
1 year limited warranty
Each point identifies the 1000V to 100V discharge times (in seconds)with high fan/low fan speed across the target area. Times are slightly higher with 230V/50 Hz unit. Times have shown to be less under typical operating environments.
1.Tested in accordance with ANSI/ESD STM3.1-2015.
2.Velocity in fpm measured at center line of air stream; all values ±10%.
3.Testing Conditions: Temperature,22℃±5℃；RH,≤60%.
Installation AAC-8 series Overhead Ionizer is designed to mount above the work area, providing even coverage without using valuable worksurface area. Mounting is a matter of personal preference. Use the included hanging kit to suspend the ionizer with its brackets, or secure its brackets to a shelf. Ensure that the mounting is secure and capable of supporting the weight of the ionizer. The power cord should be supported as well to protect the operator from any hazard.
The ideal mounting height is 18" above the worksurface, although the ionizer may be located slightly higher or lower if required. For optimum performance, ensure that the intake grills for the fans are not obstructed. Verify that the ON/OFF switch located at the back of the ionizer is in the OFF position. Plug the power cord into the ionizer, and plug the other end into a properly wired power outlet.
Occasional cleaning of the case and of the ionizing electrodes are the only routine maintenance procedures required.
Cleaning the case :
Wipe the case with a soft cloth moistened with water. If a stronger cleaning solution is required, mild soap with water may be used. The use of any other cleaning solutions is not recommended.
Cleaning the emitter pionts :
NOTE: Disconnect the power to the ionizer whenever cleaning the emitter points. When the emitter pionts become dirty, the internal circuitry of the ionizer will be automatically adjusted to emit an equal amount of positive and negative ions. Particulates on the emitter point may, however, inhibit ionization to a limited degree. If a more rigorous cleaning method is needed to remove particulate, clean the points with a cotton swab dampened with isopropyl alcohol. Access to the points is available through the rear grill. Be careful not to damage the points during cleaning.